- #Detach audio on fotomagico 5 drivers
- #Detach audio on fotomagico 5 full
- #Detach audio on fotomagico 5 tv
- #Detach audio on fotomagico 5 free
Of course, the beauty of the Bar 9.1’s truly wireless surround speakers is that you have much more freedom in terms of placement than you would with typical “wireless” surround speakers that are tethered to power cords (or in some cases, to a powered wireless unit).
#Detach audio on fotomagico 5 full
You’ll need to detach the surround speakers and place them for the full 5.1.4 effect.
#Detach audio on fotomagico 5 drivers
When the surround speakers are connected to the soundbar, their tweeters and full-range upfiring drivers boost the sound of the drivers in the main unit, essentially turning the soundbar into a 3.1.2-channel configuration.
The main JBL Bar 9.1 soundbar unit charges the wireless surround speakers when they’re attached. When you fit the speakers onto the soundbar, they snap in with a solid, satisfying thwunk, while disconnecting the modules requires pulling them straight out using a fair amount of force. A flat rectangular protuberance on the side of each surround module fits into the corresponding side of the main soundbar housing, and a set of hidden magnets holds the modules in place. When I first picked them up, I was surprised by how heavy they were indeed, each of the modules weighs a little more than two pounds, which gives each speaker a reassuringly substantial heft. Now it’s time for the wireless-and yes, we do mean wireless-surround speakers, which are packed separately in the box from the main soundbar unit. The wireless subwoofer (which, unlike the surround modules, does have a power cord), comes pre-paired to the soundbar, and in my case it connected automatically as soon as I powered it up.
#Detach audio on fotomagico 5 free
A five-foot AC cord (which is thankfully free of bulky bricks or outlet-blocking wall warts) attaches to a rear power port.
#Detach audio on fotomagico 5 tv
The JBL Bar 9.1 looks a tad more imposing with its 6.8 x 2.4 x 4.7-inch wireless surround speakers attached, which bring the soundbar’s overall length to 48.4 inches, or nearly the entire length of my 50-inch LG TV.įirst up is placing the main soundbar unit in front of your TV, or (optionally) mounting it under the TV on a wall a mounting kit for both the soundbar cabinet and the wireless surround speakers is included. Even with my low-slung 50-inch LG C9 OLED TV, the JBL Bar 9.1 only blocked a sliver of the set’s bottom edge, and the (barely there) obstruction didn’t bother me in the slightest. That’s actually relatively compact compared to similarly priced soundbars I’ve tested, and in particular the soundbar’s 2.4-inch height won’t block the bottom edge of most TVs. The main soundbar unit measures 34.8 x 2.4 x 4.7 inches with the wireless surround speakers detached.
Not all ceilings are ideal for the upfiring trick, however for its part, Dolby recommends a flat ceiling that’s between 7.5 and 14 feet high, and a vaulted ceiling won’t work. The idea behind the upfiring drivers is that they bounce sound off your ceiling, which makes for an easier alternative to installing height speakers in your ceiling. Those (total) four upfiring drivers provide the height effects for Dolby Atmos and DTS:X, the two competing immersive audio formats that the JBL Bar 9.1 supports. The two remaining height channels come from the upfiring drivers in the two wireless surround speakers, each of which comes equipped with one-inch tweeters.
On the main soundbar unit, the left, right, and center channels are powered by four racetrack (or oval-shaped) full-range drivers and three one-inch tweeters, while a pair of upfiring drivers supply audio for two of the four height channels. JBL bills its Bar 9.1 as (natch) a “9.1-channel soundbar,” but it’s more accurately described as a 5.1.4 system: In addition to the traditional left, center, right, rear surround and low-frequency effects channels (the “5.1” part), you also get front and rear height channels (the “.4” at the end).
0 kommentar(er)
